Offering fast and affordable ASTM A Jominy End Quench Test of Hardenability along with heat treating and metallurgy expertise. This standard is issued under the fixed designation A ; the number 1 These test methods are under the jurisdiction of ASTM Committee A01 on. Steel. ASTM A Determining Hardenability of Steel – Designation: A – 99 An American National S.
|Published (Last):||17 May 2015|
|PDF File Size:||16.23 Mb|
|ePub File Size:||19.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM A255 Jominy Hardenability Testing
After the Woods metal is molten, screw the stud in place so that the specimen is forced? Carbon and Sulfur Analysis.
Your Alert Profile lists the documents that will be monitored. The sheath shall preferably be made from a plain low-carbon steel. The Certified Material Test Report shall state a255 method of hardenability determination. Historical Version s – view previous versions of standard.
If the retest also has greater than 4 HRC points spread, a new specimen should be tested.
The effects of phosphorous and sulfur are not considered since they tend to cancel one another. Link to Active This link will always route to the current Active version of the standard.
It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape aetm test specimen in a standardized quench.
The accuracy of this test method and the techniques used to develop it have been documented. Cast specimens are not suitable for boron steel grades due to erratic results.
Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Very light cuts with asstm cooling and a coarse, soft-grinding wheel are recommended to avoid heating the specimen. The sample is then brought back up to austenitizing temperature as specified for alloy, and end quenched with a specialized holder for the end quench to occur.
Hardness data is given in cert format with actual curve of material being tested.
ASTM A Determining Hardenability of Steel_百度文库
It is astm a quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized astm a For this example with 0. Boron factor 5 1. You may delete a document from your Alert Profile at any time. The test consists of water quenching one end of a cylindrical test specimen 1.
Historical Astm a s — view previous versions of standard Translated Version s: You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. The Certified Material Test Report shall state the astm a of hardenability determination. Link satm Active This link will always route to the current Active version of the standard. It is the responsibility a525 the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
The mold may also be used to form a 1. It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench. The Certified Material Test Report shall state the method of hardenability determination. A tank of sufficient capacity to maintain the water temperature requirements of 6. Examples of this method are J 4? In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which correlates to a given hardness level.
A lowpower measuring microscope is suitable for use in determining the distance from the quenched end to the center of the?
This testing is indented for determining the hardenability of steels. Dimensions of the preferred specimen and of an optional specimen Note 2 are given in Fig.
ASTM A – Jominy Hardenability Testing Laboratory | SGS MSi Testing
This testing can be done on a sub-sized sample which does not meet the standard size bar dimension as governed by Appendix X1. Referenced Astm a purchase separately The documents listed below are referenced within awtm subject standard but are not provided as part of the standard. Link to Active This link will always route to the current Active version of the standard. A superscript epsilon e indicates an editorial change since the last revision or reapproval. If the document is revised or amended, you will be notified by email.
A number in parentheses indicates the w255 of last reapproval. We have no amendments or corrections for this standard. Then heat the assembly and quench in accordance with 6.