ASTM C1354 PDF

ASTM C Standard Test Method for Strength of Individual Stone Anchorages in Dimension Stone. Find the most up-to-date version of ASTM C/CM at Engineering Aug 27, Test of a kerf anchor according to ASTM C Photo courtesy The Natural Stone Institute. by Charles Muehlbauer. Natural stone products.

Author: Shakagal Fegul
Country: Burkina Faso
Language: English (Spanish)
Genre: Photos
Published (Last): 14 February 2013
Pages: 61
PDF File Size: 3.98 Mb
ePub File Size: 10.90 Mb
ISBN: 205-4-92886-863-5
Downloads: 94880
Price: Free* [*Free Regsitration Required]
Uploader: Gokus

A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Load is applied, separately, perpendicular to the surface of the panel and parallel to the surface of the panel. This test is intended to represent the interaction of the anchor with the stone panel. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Current edition approved Oct. Summary of Test Method 4. The mechanical anchor is connected to a test support.

A test load is applied perpendicular or parallel to the face of the stone panel. The test load is applied gradually using a calibrated test machine; load is increased until the stone or the mechanical anchor fails. The test as described above is repeated?

The strength of a limited length of anchor may be related to a longer length of support when the? Refer to Guide C Support Frame and Loading Device 7. In addition, the support frame shall be sufficiently stiff to limit de?

  K.AJDUKIEWICZ ZAGADNIENIA I KIERUNKI FILOZOFII PDF

ASTM C 土方石独立石桥墩的强度的标准试验方法_百度文库

The anchor shall be attached to the support frame in the same way it will be attached to the backup structure in construction. The sample of stone is supported at the c3154 end by a 25 mm 1 in. The sample of stone panel is aatm down while the upward load is applied through a single sample of anchor. The stone sample may be held down by independent anchors as shown in Fig.

The area beneath the anchor shall be 2 kept unsupported to prevent restraint of spalls that may arti? The surface between the loading plate and the stone panel sample shall be lubricated. If sealant, epoxy, c154 other form of kerf?

Alternatively, provisions may be made to distribute the load from the anchor to the stone with a soft bearing material. Stone samples shall be taken from slabs oriented relative to rift satm will be used in construction. Stone suppliers shall provide the following information: If atsm is desired to measure fracture strength of stone when it exceeds the strength of the metal anchor, an additional set of tests shall 4 More specimens may be needed depending on the variability of the test results.

If necessary, determine suitable statistical parameters to evaluate the composite variability and to select the number of specimens needed for obtaining a given minimum precision in determining the capacity of the anchorage system.

Test specimens immediately upon removing from the bath, wiping the specimen free of surface water. Observe and record the failure of the load applied to each specimen.

  BLOOD FOREVER BY MARI MANCUSI PDF

Natural Stone Testing Services

If restraint devices have interfered with the fracture plane, note it and adjust the locations of the restraint devices. The designer specifying the test shall state what de? Actual dimensions of each sample tested rather than nominal dimensions shall be measured and reported, 4 Precision and Bias A precision section will be added when sufficient data are available to indicate acceptable tolerances in repeatability and reproducibility.

The F1354 Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection c13554 any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such f1354, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address c13354 at phonefaxor service astm.