ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Tektilar Meztizuru
Country: Sierra Leone
Language: English (Spanish)
Genre: Politics
Published (Last): 12 June 2007
Pages: 277
PDF File Size: 19.9 Mb
ePub File Size: 7.85 Mb
ISBN: 766-7-64060-641-9
Downloads: 44454
Price: Free* [*Free Regsitration Required]
Uploader: Goshakar

Historical Version s – view previous versions of standard. F When approved by the purchaser, alloys or Se may be furnished. D Yield strength is the stress at which an offset of 0.

ASTM F594 Specification

Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: Unless otherwise specified, all bolts, hex f954 screws, and studs used with these nuts shall conform to the requirements of Specification F and shall be of the same alloy group.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use f549 application. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. B legend of conditions: AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after asrm.

Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

  EMG BQS SYSTEM PDF

SH – Machined from strain hardened stock or cold worked to develop f5594 specific properties. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements. A Minimum values except where shown as maximum or as f94 range. ASTM F covers seven groups of stainless steel alloys, zstm twelve austenitic, two ferritic, four martensitic and one precipitation hardening.

C The yield and tensile strength values for full size products shall be computed by dividing xstm yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties.

A Tensile stress areas are computed using the following formula: D594 When approved by the purchaser, alloy F may be furnished. ASTM does not give any warranty express or implied asmt make any representation that the contents of this abstract are accurate, complete or up to date.

Free Technical Information

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. CW – Headed and rolled from annealed stock thus acquiring a degree f5594 cold work. A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed.

  JBL CONTROL 19CS PDF

Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has been completed. The values given in parentheses are mathematical conversions to SI units that are f54 for information only and are not considered standard.

Free Technical Information | Industrial Fasteners Institute

The finished fasteners shall meet the applicable mechanical properties. Link to Active This link will always route to the current Active version of the standard. This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number 5f94 alloys in common use and intended for service applications requiring general corrosion resistance. Condition CW – When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and then cold worked to develop ast specified properties.

This abstract is a brief summary of the referenced standard.