ASTM G102 PDF

Description. ASTM G Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements. View more. ASTM G()e1. Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements. ASTM-G Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements – corrosion.

Author: Kijora Tygokree
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Art
Published (Last): 3 August 2006
Pages: 59
PDF File Size: 7.31 Mb
ePub File Size: 11.86 Mb
ISBN: 256-5-26135-867-9
Downloads: 19559
Price: Free* [*Free Regsitration Required]
Uploader: Zulkigor

ASTM D standar A number in parentheses indicates the year of last reapproval.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Calculation methods for converting corrosion current density values to either mass loss rates or average penetration rates are given for most engineering alloys.

In addition, some guidelines for converting polarization f102 values to g1022 rates are provided. V102 practice is intended to provide guidance in calculating mass loss and penetration rates for such alloys. Some typical values of equivalent weights for a variety of metals and alloys are provided. The conversion of these results to either mass loss or penetration rates requires additional electrochemical information.

Astk approaches for estimating this information are given. Current edition approved Feb. Originally published as G — Last previous edition G — 89 e1. Corrosion Current Density 4.

This is accomplished by dividing the total current by the atsm area of the electrode exposed to the solution. It zstm assumed that the current distributes uniformly across the astmm used in this calculation.

In the case of galvanic couples, the exposed area of the anodic specimen should be used. This calculation may be expressed as follows: Icor icor 5 A 1 where: A, and A 5 exposed specimen area, cm2. Other units may be used in this calculation.

In some computerized polarization equipment, this calculation is made automatically after the specimen area is programmed into the computer. A sample calculation is given in Appendix X1. For pure elements, the equivalent weight is given by: W 5 the atomic weight of the element, and n 5 the number of electrons required to oxidize an atom of the element in the corrosion process, that is, the valence of the element.

It is usually assumed that the process of oxidation is uniform and Copyright? If this is not true, then the calculation approach will need to be adjusted to re? In addition, some rationale must be adopted for assigning values of n to the elements in the alloy because many elements exhibit more than one valence value.

ASTM G102 Standard Practice

Consider a unit mass of alloy oxidized. The electron equivalent for 1 g of an alloy, Q is then: Q 5 Wi 3 where: Therefore, the alloy equivalent weight, EW, is the axtm of this quantity: Wi 4 unless a better basis is available. A sample calculation is given in Appendix X2 1. It is best if an independent technique can be used to establish the proper valence for each alloying element.

  JURDJEVIC GEOMETRIC CONTROL THEORY PDF

Sometimes it is possible to analyze the corrosion products and use those results to establish the proper valence. Another approach is to measure or estimate the electrode potential of the corroding surface.

Equilibrium diagrams showing regions of stability of various phases as a function of potential and pH may be created from thermodynamic data. These diagrams are known as Potential-pH Pourbaix diagrams and have been published by several authors 2, 3.

The appropriate diagrams for the various astmm elements can be consulted to estimate the stable valence of each element at the temperature, potential, and pH of the contacting electrolyte that existed during the test. NOTE 2—Some of the older publications used inaccurate thermodynamic data to construct the diagrams and consequently they are in error. Normally only elements above 1 mass g02 in the alloy are included in the calculation.

In cases where the actual analysis of an alloy is not available, it is conventional to use the mid-range of the composition speci?

ASTM G Standard Practice – Free Download PDF

B Registered trademark Haynes International. NOTE 2—Mid-range values were assumed for concentrations of alloying elements. NOTE 3—Only consistent valence groupings were used.

NOTE 4— Eq 4 was used to make these calculations. Values of 65 and mV are asfm commonly used. In most programmable potentiodynamic polarization equipment, the current is converted to current density automatically and the resulting plot is satm i versus E.

This is equivalent to the calculation shown in 4. B5 ba bc 2. A sample calculation is given in Appendix X4. The reaction under mixed control will have an apparently larger b value than predicted for an activation control, and a plot of E versus log I will tend to curve to an asymptote parallel to the potential axis.

The estimation of a B value for situations involving mixed control requires more information in general and is beyond the scope of this standard. In general, Eq 7 and Eq 8 may be used, and the corrosion rate calculated by these two approximations may be used as lower and upper limits of the true rate.

NOTE 4—Electrodes exhibiting stable passivity will behave as if the anodic reaction were diffusion limited, except that the passive current density is not affected by agitation. Several approaches have been proposed based on analyses of electrode kinetic models.

See Refs for more information. In general, Tafel slopes are given by KRT b 5 nF 9 where: For simple one electron reactions, K is usually found to be 2. B icor 5 R 10 p where: A sample calculation is given in Appendix X5. The effect of solution resistance is a function of the cell geometry, but the following expression may be used to approximate its magnitude. Rp 5 Ra 2 rl 11 where: Ra 5 the apparent polarization resistance, ohm cm2, r 5 the electrolyte resistivity in ohm cm, l 5 the distance between the specimen electrode and the Luggin probe tip, or the reference electrode in cm, and Rp 5 the true polarization resistance in ohm cm2.

  DR.JILL AMMON-WEXLER PDF

A sample calculation is given in Appendix X6. In this case, the magnitude of the error is proportional to scan rate. The error is illustrated by Eq The capacitance charging effect will cause the calculated polarization resistance to be in error.

Generally, this error is small with modest scan rates In cases where the corrosion potential is within 50 to mV of the reversible potential of the corroding electrode, the electrochemical reactions will occur simultaneously on the electrode surface. This will cause either the anodic or cathodic b value to appear smaller than the corrosion reaction above.

Consequently, the Stern-Geary constant B will be in?

In this case, the concentration of the corroding electrode ions is generally of the same magnitude or higher than other ions participating in the corrosion process in the electrolyte surrounding the electrode. Other redox couples that do not necessarily participate in the corrosion reaction may have similar effects.

This is especially true g02 metals exhibiting passive behavior. Therefore, the gram equivalents of the dissolved components asttm given by Eq 3.

The American Society for Testing and Materials takes no position g012 the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and astn risk of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.