DIXELL XW60L PDF

Dimensions w x h x l: 0 x 0 x 0 mm. Weight net: kg. Power supply: VAC. Display digits: 3. Keyboard: push buttons: 6. Sensor input thermostat: NTC/PTC. XW60L – XW60V. 1. GENERAL WARNING set. To display and modify target set point; in programming mode it selects a parameter or confim an operation. NEW DIXELL XW60L-4N0C0N controller V REFRIGERATION CONTROLLER: : Industrial & Scientific.

Author: Mubei Masida
Country: Cameroon
Language: English (Spanish)
Genre: Career
Published (Last): 5 January 2006
Pages: 217
PDF File Size: 17.8 Mb
ePub File Size: 10.82 Mb
ISBN: 653-9-83064-290-5
Downloads: 35618
Price: Free* [*Free Regsitration Required]
Uploader: Tygokree

Fit the probe where it is not accessible by the End User. The instrument must not be opened.

Page of 4 Go. This manual is part of the product vixell should be kept near the instrument for easy and quick reference. The instrument shall not be used for purposes different from those described hereunder.

Check the supply voltage is correct before connecting the instrument. Do not expose to water or moisture: In case of failure or faulty operation send the instrument back to the distributor or to “Dixell s. Consider the maximum current which can be applied to each relay see Technical Data.

Ensure that the wires for probes, loads and the power supply are separated and far enough from each.

CONTROLLER DIXELL XW60L-5N0D1-X

In case of applications in industrial environments, the use of mains filters our mod. FT1 in parallel with. Model XWL, 38x mm format, is microprocessor based controller suitable for dxell on medium or.

  IDIOTA FIODOR DOSTOJEWSKI PDF

It is provided with four relay outputs to control compressor, defrost – which. It is also provided with three NTC probe inputs, one for temperature control, one to control the defrost end. There are two digital inputs free contact. RTU compatible monitoring system and to programme the parameter list with the “Hot Key”. The regulation is performed according to the temperature measured by the thermostat probe with a positive.

In case of fault in the thermostat probe the start and stop of the compressor are timed through parameters.

When defrost is not in progress, it can be activated the keypad by holding the. The compressor operates in continuous mode for the time set through the “CCt” parameter. Three defrost modes are available through the “tdF” parameter: The defrost interval is control by means of parameter “EdF”: At the end of defrost the drip time is controlled through the “Fdt” parameter. The fan control mode is selected by means of the “FnC” parameter:.

After defrost, there is a timed fan delay allowing for drip time, set by means of the “Fnd” parameter.

Dixell XW60L-5N0C1

An additional parameter “FSt” provides the setting of temperature, detected by the evaporator probe, above. This can be used to make sure circulation of air only if his temperature is lower. To display and modify target set point; in programming mode it selects a parameter or confirm an.

By holding it pressed for 3s when max or min temperature is displayed it will be erased.

To see the max. By holding it pressed for 3s the fast freezing cycle is started. To see the min stored temperature; in programming mode it browses the parameter codes or. By holding it pressed for 3s the defrost is started. Each LED function is described in the following table. Function of the LEDs placed xxw60l the left top side of buttons:.

  ACCESS 2007 PROGRAMMAZIONE VBA PDF

XW60L – DIXELL Israel

The “Lo” message will be displayed followed by the minimum temperature recorded. The “Hi” message will be displayed followed by the maximum temperature recorded. To reset the stored temperature, when max or min temperature is displayed:. Push and immediately release the SET key: To memorise the new set point value push the SET key again or wait 10s. Push the DEF key for more than 2 seconds and a manual defrost will start.

To enter the parameter list “Pr1” user accessible parameters operate as follows:. The instrument will show the first parameter present in “Pr1”. Add to my manuals Add. Comments to this Manuals Your Name. Enter text dixel picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again.

Got it, continue to print. Don’t have an account?