FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from
| Author: | Zutilar Kajikinos |
| Country: | Nigeria |
| Language: | English (Spanish) |
| Genre: | Photos |
| Published (Last): | 28 March 2004 |
| Pages: | 268 |
| PDF File Size: | 11.99 Mb |
| ePub File Size: | 11.51 Mb |
| ISBN: | 863-6-23228-816-4 |
| Downloads: | 22469 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Taushicage |
This chapter lists specifications including output ratings, control system, external dimensions and protective functions. Torque limit time 0. Using the optional multi-function keypad allows you to start and stop the motor, monitor running status, and switch to the menu mode. Increase F26 Motor Sound Carrier frequency. When the replacement is frfnic, contact your Fuji Electric representative. Mounting the covers Put the front cover to the inverter case so that its bottom engages with the hinges provided on both sides of the case.
When employing external cooling At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally. Inquiries About Product And Guarantee 7. Grounding terminals Mnual Be sure to ground either of the two grounding terminals for safety and noise reduction. List Of Periodical Replacement Parts Each part of the product has its own service life that will vary according to the environmental and operating conditions.
Refer to Chapter 5, Section 5. Please do not use it with other products.
Set up L02 for correct data. Page Name of option Function and application Insert an MC in the power source side of the inverter in order to: If any problems persist after the above recovery procedure, contact your Fuji Electric representative. Tuning procedure What follows gives you a tuning procedure of the inverter for a motor using a multi-function keypad option. Precautions for use Driving a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur.
Enter text from picture: Note 2 To protect wiring, insert a molded case circuit breaker MCCB or an earth leakage circuit breaker ELCB with overcurrent protection of the type recommended for the inverter between the commercial power supply and the inverter. Designed for Elevating Machinery.
For the tuning procedure, refer to the instruction manual of the option card. Page 54 F codes: Chapter 4 Running The Motor U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly. Don’t have an account? Page 24 – Terminal arrangement and screw specifica Manusl 9 Select an inverter according to the applicable motor ratings listed in the standard specifications table for the inverter.
Brake control by liff current Operation level 0 to ON delay time 0.
FUJI ELECTRIC FRENIC-LIFT SERIES INSTRUCTION MANUAL Pdf Download.
Release the mechanical brake. Page 81 [ 24 ] Out of control speed Problem An out of control error PG failure occurs between the speed command and the speed feedback. Lower the temperature around the motor. CAN bus An abnormal communication with the main body of the inverter is detected when communication the CAN bus is used, and the inverter is stopped. Don’t show me this message again.
Fuji Electric FRENIC-Lift series Instruction Manual
Otherwise, the inverter may be broken if you turn the power ON. Icons The following icons are used throughout this manual.
For the inverters with a capacity of 22 kW or below, wait at least 5 minutes; Mamual so could cause fire. Possible Causes What to Check and Suggested Measures 1 No power supplied to the Check the input voltage, output voltage and interphase voltage unbalance.
Page 40 Table 2. Page 17 When employing external cooling At the shipment time, the inverter is set up for mount inside your mwnual or enclosure so that cooling is done all internally.
Table of Contents Add to my manuals Add. On the bottom are no case fixing screws. Page 14 2 Warning plates Figure 1. Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances Page