GATEWAY MA2 MANUAL PDF

Find the user manual and the help you need for the products you own at ManualsOnline. I got an old laptop model MA2 without powersupply. SetIP command to see and change the IP addresses of the console. This command can be used to change both Ethernet connectors and even set a gateway. Requirement: STP (shielded twisted pair) cable with RJ45 connector, min. Cat 5e . To connect Ethernet port 1: Connect one end of an Ethernet cable to the.

Author: Dairisar Yozshurg
Country: Ukraine
Language: English (Spanish)
Genre: Career
Published (Last): 4 November 2014
Pages: 106
PDF File Size: 1.27 Mb
ePub File Size: 13.64 Mb
ISBN: 996-7-63412-141-7
Downloads: 30279
Price: Free* [*Free Regsitration Required]
Uploader: Zulugar

Dell Latitude, Vostro, and Precision. Mayo Hardware Sat Jul 24, It powered right up! I have resistance on the POS pin to the shield of the dc port.

Thanks for your help Ken. One mx2 should read infinity, the other may be from to Ohms. I put a new port on the board. Mason Man Fri Jun 18, Here are all the consoles in your system listed.

Gateway Official Site: Worldwide

Then type the new IP address – and reboot. My thinking is there is a grounding problem with the DC gateqay just not sure to solve this one. Mayo Hardware Sat Aug 14, Ford Mon Jul 16, Hi mayo I have a gateway ma3 and also no powe after close inspection i see the power diode marked pd33 is blown so I cant make the number on it to replace it.

  GHIDUL CERCETATORULUI UMANIST PDF

The [coil] on the circuit board is actually a jumper, since the uH microHenry is so high and no forward direction needed because the diode blocks reverse current. Neil Wed Jun 23, Damien Mon Apr 26, You may want to view the latest help version. Ok I read the manual and I only get 4 flashing red lights after hitting the power button.

Set the IP address in the console

Mayo Hardware Mon Jul 16, Actually that diagnosis should be evident that your power supply is defective or going bad. The Amnual Will reboot with memory in. The charge light comes on then goes out. Or the CMOS battery is dead or too low. The motherboard is slightly different than the MA7 you describe here.

Sorry, I don’t keep records of part numbers and where they are bought. Anonymous Sat Aug 07, Can Someone help me please.

Gateway Laptop MA2 User’s manual |

I’ll attempt to re-create the same test here. Further testing is necessary.

StormJumperJul 23, Log in or Sign up. So either leg will suffice. I haven’t checked the mosfet, but i’m not sure were that is. Check the front center of the DC ms2 the rear for continuity.

Chance Sat Aug 14, It now charges the battery and powers the laptop. As soon as I disconnect the external monitor I loose power. I can also see 19v at the battery charge port, but I can still not get the laptop to either charge the battery, or even run without the battery.

  1N3070 DATASHEET PDF

Sorcerer Thu May 20, I have done 10 of these units and know how to by pass the 3rd layer board and mx2 the center pin dc jack to the fuse, so far they have all worked out great, learned the agteway way as my first one needed a new motherboard, the MA7 is a nightmare.

How do you test them if so? Each console have two IP addresses – one for each Ethernet connector on the back.

Can’t boot into anything but my bios BackpackerMw2 28, at 1: Glad to hear you got your problem solved!!!! Hope that helps somebody. Not sure what the four flashes are, maybe the battery is shorted It may be marked AO, which is common.

Gatteway pictures show what the diode looks like and how I bypassed it on one unit. Windows OS and Software. So during all this boot and reboot do you ever get to the Desktop?